- Home
- Portfolio Lighting Parts & Accessories
- Portfolio Model Parts Directory
- Portfolio 0206819 / WL121MBKP
📦Shop Portfolio-Compatible Lighting Parts on AmazonAffiliate link · We may earn a commission.🔧Find Discontinued Portfolio Parts on eBayAffiliate link · We may earn a commission.
Confirmed model facts before you start
The factory manual pairs item 0206819 with model WL121MBKP and item 0208502 with model WL120MWWP.
The manual specifies one standard-base lamp: up to 60 watts incandescent or 13 watts CFL.
The documented assembly uses a mounting strap, two decorative nuts, screws/nuts, a fixture cover, shade and three E3 wire connectors.
Before ordering anything, compare the label and physical dimensions with the Portfolio model lookup, model parts directory and parts hub.
Do not confuse 0206819 with the white sibling
The manual covers two sibling lanterns, but the item number matters when matching visible parts. Use 0206819 and WL121MBKP together when searching for the original finish and appearance. The mounting and electrical logic can overlap with WL120MWWP, yet a shade, cover or decorative nut that fits mechanically may still be the wrong color or finish. Photograph the label and front profile before removing the fixture.
Field note: Work from the symptom toward the failed component. Record what changes after each test instead of replacing several parts at once. That preserves the evidence you need to tell a fixture fault from a wiring, mounting, charging or control problem on 0206819 / WL121MBKP.
A new bulb does not prove the fixture is bad
If the lantern is dark, first confirm the wall switch and breaker, then test with a known-good standard-base bulb within the fixture rating. If the known-good lamp remains dark, shut off the breaker and inspect the socket, neutral connection and wire connectors. A loose neutral can make an outdoor lantern intermittent without obvious damage. A center contact flattened too deeply in the socket can also prevent a bulb from making reliable contact.
Field note: Work from the symptom toward the failed component. Record what changes after each test instead of replacing several parts at once. That preserves the evidence you need to tell a fixture fault from a wiring, mounting, charging or control problem on 0206819 / WL121MBKP.
Shade and fixture-cover service
The manual identifies the shade and fixture cover as separate components. When either is cracked, measure the actual part before shopping because family resemblance is not enough. Record height, widest diameter, opening diameter, retaining-tab positions and the way the cover twists or seats. If a replacement shade is slightly too tall or its lip geometry differs, forcing it can crack the part or leave the lantern open to rain.
Field note: Work from the symptom toward the failed component. Record what changes after each test instead of replacing several parts at once. That preserves the evidence you need to tell a fixture fault from a wiring, mounting, charging or control problem on 0206819 / WL121MBKP.
Mounting strap and decorative-nut problems
A lantern that rocks on the wall may have a loose mounting strap, screws set to the wrong projection, stripped hardware or an outlet box that is not flush with the siding. Do not solve a structural mounting problem by over-tightening the decorative nuts. With power off, verify that the box is secure, the strap is firmly attached and the fixture backplate sits flat. Exterior gaps around the mounting surface should be weather-sealed appropriately without trapping water inside the box.
Field note: Work from the symptom toward the failed component. Record what changes after each test instead of replacing several parts at once. That preserves the evidence you need to tell a fixture fault from a wiring, mounting, charging or control problem on 0206819 / WL121MBKP.
Corrosion and water intrusion
Look closely at the socket shell, bulb base, wire-entry area and lower shade. Green copper corrosion, rust staining or white mineral deposits indicate moisture has been present. Drying the lantern may restore it temporarily, but recurring water entry means the source must be corrected. If corrosion has migrated into the socket contacts or wire splices, replacement of the electrical component or complete lantern is safer than repeated cleaning.
Field note: Work from the symptom toward the failed component. Record what changes after each test instead of replacing several parts at once. That preserves the evidence you need to tell a fixture fault from a wiring, mounting, charging or control problem on 0206819 / WL121MBKP.
Choosing a modern replacement
When the original 0206819 lantern cannot be repaired, match the replacement to the outlet-box location, backplate coverage, projection from the wall and bulb access. A medium-base fixture that accepts a replaceable LED bulb can simplify future maintenance. Do not choose by style alone: the new backplate must cover the existing box and the fixture must be rated for the exterior exposure where it will be installed.
Field note: Work from the symptom toward the failed component. Record what changes after each test instead of replacing several parts at once. That preserves the evidence you need to tell a fixture fault from a wiring, mounting, charging or control problem on 0206819 / WL121MBKP.
Symptom-to-fix table
Completely deadConfirm source power or solar charge, then test the simplest serviceable component before opening the housing.IntermittentLook for loose contacts, corrosion, moisture, weak battery or wiring that changes when the fixture moves.Dim outputCheck lamp/battery condition, dirty optical surfaces, voltage/charge availability and heat or corrosion at contacts.Water insideDisconnect power where applicable, dry the fixture, identify the entry path and replace damaged electrical parts before reuse.Broken mountingMeasure original geometry and hardware; do not let improvised mounting create a falling-fixture or water-entry hazard.
This record is especially valuable when factory replacement parts are discontinued because it lets you compare a modern substitute by function and dimensions instead of by appearance alone.
How to document a discontinued Portfolio fixture
LabelPhotograph the full model/item number before cleaning the label.ElectricalRecord voltage, bulb/battery type and any wattage or chemistry markings.MechanicalMeasure mounting diameter, backplate/post fit, screw spacing and visible part dimensions.ConditionPhotograph corrosion, cracks, water tracks and heat discoloration before disassembly.ReplacementKeep the original until the new part is installed so you can compare fit directly.
This record is especially valuable when factory replacement parts are discontinued because it lets you compare a modern substitute by function and dimensions instead of by appearance alone.
Related Portfolio repair resources
Continue with Portfolio troubleshooting, replacement parts, manuals, discontinued Portfolio lighting and the technical archive.