- Home
- Portfolio Model Parts Directory
- Portfolio 0122466 / LPC-11263/2
What the surviving documentation confirms
The surviving manual identifies item 0122466 as Portfolio model LPC-11263/2, a flushmount ceiling fixture. It uses two medium-base lamps: the manual specifies up to two 60-watt medium-base incandescent bulbs or two 13-watt medium-base CFLs. Documented package parts include the ceiling pan, glass and ring; installation hardware includes a crossbar, mounting nipple, hex nut, green ground screw, wire connectors and finial. The original replacement-parts list is unusually useful because it confirms that several mounting pieces were separately identified.
Both bulbs are out: test upstream before replacing sockets
Two simultaneous dark lamps are less likely to be two independent burned-out bulbs. Turn off the breaker, verify both lamps in a known-good fixture, then inspect the wall switch, supply connection, neutral and fixture wire connections. The original manual’s troubleshooting sequence includes lamp replacement and checking power. If you are not equipped to safely verify line-voltage wiring, stop and use a qualified electrician.
One socket works and one does not
A one-sided failure points toward the lamp, socket or local internal connection. With the breaker off and absence of voltage verified, inspect the center contact and shell for heat discoloration, looseness or corrosion. Do not bend or probe energized socket contacts. If the socket is damaged, replacement must match its mounting, temperature rating, lead arrangement and lamp base; otherwise replacing the complete fixture may be the safer route.
Missing glass, ring or finial
For a discontinued flushmount, appearance parts are often harder to source than electrical hardware. Measure the glass outside diameter, center opening if present, depth, ring diameter, nipple thread and finial fit. The manual documents a ceiling pan, glass, ring and finial arrangement, so a shade that merely has the right diameter may still fail to mount. Keep the original ring and finial until a replacement has been physically test-fitted.
Mounting crossbar and nipple problems
The fixture is supported through a crossbar and mounting nipple secured to the outlet-box system. If the fixture hangs crooked, do not compensate by overtightening the glass or finial. Shut off power and inspect the outlet box, crossbar, nipple, hex nut and ceiling pan alignment. A loose or damaged electrical box is a building-wiring issue, not a cosmetic fixture problem, and should be corrected before reinstalling the light.
Identify the exact fixture before ordering anything
For 0122466 LPC-11263/2, portfolio used retail item numbers, model numbers and family names in different places. Photograph the label before cleaning it and keep every suffix. Search both the model and item number. A visually similar fixture can use a different lamp, connector, battery, mounting pattern or voltage. The fastest way to waste money on a discontinued product is to buy by appearance alone.
Symptom-first diagnostic order
For 0122466 LPC-11263/2, start by deciding whether the failure affects one fixture, one section, or the entire system. Compare the failed unit with a working neighbor when possible. Then test the simplest serviceable components before disassembling structural parts. This sequence preserves evidence: power source, local connection, lamp or battery, socket or contacts, moisture, then housing and mounting. Change one variable at a time so a temporary recovery actually tells you something.
Parts sourcing when the original part is discontinued
For 0122466 LPC-11263/2, separate electrical compatibility from mechanical compatibility. For electrical parts, match voltage, base or connector, wattage limits and environmental rating. For mechanical parts, record thread diameter, pitch, length, mounting-hole spacing, glass dimensions and clearances. Generic hardware can sometimes restore a fixture, but only when it does not compromise grounding, weather resistance, strain relief or heat clearance.
When repair stops making sense
For 0122466 LPC-11263/2, a sound housing with a failed serviceable lamp, battery, connector or mounting screw is a good repair candidate. Repeated water entry, charred wiring, cracked load-bearing parts, badly corroded sockets, brittle insulation or an insecure mounting surface shift the decision toward replacement. The goal is not to preserve every original component; it is to preserve a safe, serviceable lighting system without guessing at critical specifications.
Build a service record for the next failure
For 0122466 LPC-11263/2, before closing the repair, record the model/item number, location, measured voltage where relevant, replacement part used, date, and a photo of the finished connection. For a row or kit, label fixtures by position. This turns the next failure into a comparison problem instead of a new investigation and is especially valuable for Portfolio products whose retail listings and original replacement inventories have disappeared.
Use the original hardware stack as your reference
The LPC-11263/2 manual documents a crossbar, mounting nipple, hex nut, ground screw, wire connectors and finial. If a used fixture arrives in a box of loose hardware, do not improvise the order from appearance. The nipple length and nut position determine how the ceiling pan and glass/ring assembly sit. Photograph the stack during disassembly and keep original hardware grouped until you know exactly which pieces require replacement.
Choose LED bulbs without creating a fit problem
Two medium-base LED bulbs can reduce heat and energy use compared with the original incandescent allowance, but verify physical fit inside the glass before buying a multi-pack. Bulb shoulders, length and driver housings vary. Stay within the fixture’s documented maximum lamp limits, choose bulbs suitable for enclosed fixtures when the globe creates an enclosed environment, and confirm dimmer compatibility if the wall control is a dimmer.
Glass replacement requires measurements, not a model guess
If the original glass is broken, collect every fragment safely enough to determine shape and thickness without handling sharp edges unnecessarily. Measure the ring opening, glass outside diameter, depth and the way the glass is retained. Search by both 0122466 and LPC-11263/2, but expect original decorative glass to be harder to find than electrical hardware. A universal shade is only useful if the retention geometry and clearances match the fixture.
Final verification after service
After reinstalling the LPC-11263/2, restore power only after the glass, ring and finial are secure and no wires are pinched at the ceiling pan. Verify both lamps operate without flicker and that the fixture sits firmly against the ceiling. Any movement at the electrical box, unusual heat, arcing sound, or burning odor warrants immediate shutdown and professional inspection.
Related Portfolio repair resources
For broader diagnosis, use the portfolio flush mount lighting, portfolio lighting replacement globes and covers, plus the Portfolio model parts directory and master model technical database.