- Home
- Portfolio Lighting Parts & Accessories
- Portfolio Model Parts Directory
- Portfolio 00299 / 0030661
📦Shop Portfolio-Compatible Lighting Parts on AmazonAffiliate link · We may earn a commission.🔧Find Discontinued Portfolio Parts on eBayAffiliate link · We may earn a commission.
Model 00299 and item 0030661 are one kit
The original Portfolio manual cover identifies ITEM #0030661 and MODEL #00299 and describes the product as a 6 CT PATH LIGHT KIT. Treating 0030661 as a separate model would split repair information for the same product. When searching old listings or parts, use both numbers because retailer records often emphasize the item number while manuals emphasize the model.
The manual gives unusually useful replacement-part numbers
The original replacement list names top cover 301001-0083OL, middle ring 302001-0013OL, plastic lens 990706-0051TR, rubber 990532-0063BK, bottom cover 302003-0023OL, wedge base and wire 990323-0043BK, fixture cover 302005-0012OL, post 303002-0052OL, stake 303003-0036BK and bolt 990501-6134SA. Even if those parts are no longer stocked, these numbers help distinguish the correct fixture family and can make used-part searches much more precise.
If all six lights are dark, start upstream
Six lamps failing simultaneously usually points toward a shared cause before six separate fixture failures. Confirm the transformer has power, its control mode is calling for lights, and the low-voltage output/cable connection is intact. The original troubleshooting table specifically lists an unpowered transformer as a cause of no light. If the transformer is working, move to the trunk cable and first connection rather than opening every fixture at once.
If one light is dark, inspect bulb and connector first
The original troubleshooting information identifies a failed bulb and connector pins that do not pierce the cable correctly as causes. That gives owners a sensible order: compare the dead fixture with a working neighbor, test/replace the lamp with the correct type, then inspect the connector for clean, firm contact with the landscape cable. Do not keep tightening a damaged piercing connector indefinitely; a deformed housing or corroded contact is a replacement candidate.
Broken stakes are a mechanical problem, not an electrical failure
Portfolio’s manual tells installers not to hammer stakes into hard soil. Years later, broken stakes are common because plastic sees soil movement, mower contact and freeze/thaw stress. If the light still works, preserve the electrical fixture and replace only the stake when possible. Measure the post/stake interface rather than assuming every Portfolio stake is interchangeable. The original stake number 303003-0036BK is useful evidence, and archived retailer Q&A specifically mentions owners looking for stake compatibility with item 0030661/model 00299.
Lens, rubber and housing parts protect more than appearance
The plastic lens and rubber component help keep the optical and lamp area assembled as designed. A cracked lens or missing seal can allow contamination and moisture to accelerate socket/contact trouble. When a lens is unavailable, measure outside diameter, seating lip, height and attachment method before considering a substitute. Do not seal a fixture permanently with an adhesive that prevents future lamp service unless the original design supports it.
Check transformer loading before adding or changing lamps
The manual recommends keeping total bulb consumption below the transformer’s full rating. That is important if the original six-light kit has been mixed with additional fixtures over the years. Inventory every connected lamp/fixture on the transformer rather than counting only these six. A transformer that worked with the original kit may become overloaded after later additions, while an LED retrofit may reduce load but still leave connector and cable faults untouched.
Voltage-drop symptoms can mimic a bad fixture
If the lights nearest the transformer look normal but distant fixtures are dim, yellow, intermittent or fail under load, inspect cable length, conductor size and every connection along the run. A single high-resistance connector can rob voltage from downstream fixtures. Compare voltage at the transformer and at the far end under operating load if you have the proper meter and know how to use it. Do not solve every dim-light complaint by installing a larger transformer.
How to replace one fixture without making the set look mismatched
When an original 00299 fixture cannot be saved, record fixture height, finish, light distribution and lamp color before choosing a replacement. A technically compatible low-voltage path light can still look wrong beside five originals. For a highly visible walkway, moving the odd replacement to an endpoint or replacing fixtures in pairs may look better than inserting one noticeably different fixture in the middle.
When to retire the whole six-light kit
A single broken stake, lamp or connector is a repair problem. Widespread brittle plastic, repeated water intrusion, multiple damaged sockets and a deteriorated trunk cable can make a system-level replacement more sensible. Separate the fixture condition from the transformer condition: you may be able to retain a healthy transformer and cable while replacing fixtures, or retain sound fixtures while replacing a failed transformer.
Related Portfolio landscape resources
For broader research, use the Portfolio model-number lookup, model parts directory, manuals library, and troubleshooting hub. Those pages help separate an exact-model problem from a system problem and keep replacement research tied to the label on the product rather than to appearance alone. Continue with the Portfolio landscape lighting hub and transformer master guide when the symptom affects more than one light.
Build a six-position fault map before taking the system apart
Number the six fixtures from transformer outward and record each one as normal, dim, intermittent or dead. Then note whether a symptom changes when the cable or connector is gently disturbed with power off before retesting. A pattern matters: fixture 4 dead while 5 and 6 work suggests a local fixture/connector fault, while fixtures 4 through 6 all failing can indicate a cable or connection problem upstream of fixture 4. This simple map prevents random part swapping and preserves evidence about where voltage is being lost.
LED conversion: reduce load without hiding compatibility problems
Owners often replace the original lamps with LEDs to reduce energy use and heat. That can be sensible, but select lamps designed for the transformer output and the fixture’s socket/enclosure. Compare physical length and diameter as well as electrical ratings. After conversion, test all six positions at night. If LEDs flicker or fail to start while halogen lamps worked, investigate transformer/LED compatibility rather than assuming all new lamps are defective. Keep one known-good original-style lamp for diagnosis if safe and available; it can help separate fixture wiring faults from lamp-electronics behavior.